An antiblock agent for PE film works by placing fine silica particles at the film surface so that layers touch at fewer points and separate cleanly. The trade-off is haze, coefficient of friction and dispersion quality, so the right grade and dosage are the lowest addition that meets your opening target without pushing optics or COF out of specification.
Blocking is one of those defects that rarely shows up on the line and almost always shows up at the customer. A blown or cast PE film winds well, passes its haze check, and then sticks in the roll after storage, slows the bag machine or refuses to open at the filling station. The usual response is to add more antiblock. That fixes opening, but often at the cost of clarity, a shift in slip behaviour, or gels from poorly dispersed silica. This article explains what an antiblock silica actually does in a PE film, which properties move haze and COF, and a dosage ladder that finds the balance point in a few trials rather than many.
Blocking happens when two smooth film surfaces come into such close contact that they adhere. Polyethylene is soft, its surfaces are very flat after extrusion, and low-molecular-weight fractions, residual heat in the roll and winding tension all make the contact tighter. Once the layers are pressed together over a large area, the force needed to separate them rises sharply.
An inorganic antiblock such as precipitated silica works mechanically. Particles near the surface create micro-roughness that holds the layers slightly apart, so they touch at the particle tips instead of over the full area. Less real contact means a lower opening force. Because the effect depends on particles that actually sit at or near the surface, what matters is not only how much silica is added but how it is distributed: in a coextruded structure it belongs in the skin layers, and in any structure it must be dispersed well enough that each particle does its job rather than forming agglomerates.
Every antiblock particle that roughens the surface also scatters light and changes how the film slides. The three costs are related but not identical:
Dispersion is the hidden fourth cost. Silica that is not broken down and wetted in the melt shows up as gels, fish-eyes or streaks and can raise screen-pack pressure. These defects are not fixed by changing the dosage; they point to the masterbatch, the grade or the processing conditions.
Censil puts forward three grades for the plastic film antiblock track, each with a defined role in the screening:
| Grade | Material | Where it sits |
|---|---|---|
| CENSIL 773 | Low-iron, high-purity precipitated silica | The route where film optics matter; usually the first antiblock candidate for clear packaging film and its masterbatch. |
| CENSIL 779 | Low-iron, high-purity precipitated silica | Same low-iron platform, aimed at tighter downstream appearance; also the powder route for masterbatch plants whose customers judge the film by eye. |
| CENSIL 185P | Precipitated silica powder | Conventional precipitated comparison route; run it beside 773 or 779 when cost position has to be part of the decision. |
For a clear PE packaging film, a sensible first trial runs CENSIL 773 as the lead candidate with CENSIL 185P beside it as a comparison, so that the gap in optics and opening between the low-iron and conventional routes is measured rather than assumed. If the film goes to an end user who inspects it by eye, add CENSIL 779. Censil does not publish typical-value tables for these grades; the controlled TDS, lot COA and SDS arrive with the sample and are the documents your evaluation should run on. Grade positioning across the full family is set out on the grade specifications page.
Because opening improves and optics worsen as dosage rises, the useful question is where the curves cross your specification limits. A short, structured ladder answers that faster than adjusting one trial at a time.
Write down the maximum haze, the COF window the converter needs, and the opening or blocking-force target, with the test method for each. Without agreed limits, every result becomes a debate.
Use the same resin lot, slip package, line, melt temperature, blow-up ratio or chill-roll settings and gauge for all runs. If the film is coextruded, add antiblock to the skin layers only and keep the layer ratio fixed.
Bracket your current addition with lower and higher steps, delivered through the same masterbatch carrier. Run the lead grade and the comparison grade over the same ladder so each step is a true A/B.
Let slip additives bloom and the film age under realistic storage conditions before measuring blocking force and COF. Measure haze and clarity on the same samples, and inspect for gels and streaks.
Plot opening force, haze and COF against dosage for each grade. The working dosage is the lowest step that meets the opening target with haze and COF still inside limits, plus a margin for lot-to-lot variation.
Record extrusion data at each step as well: screen-pack pressure, motor load and bubble or web stability. A grade that wins on optics but loads the screen pack quickly carries line risk that the lab results will not show.
A useful sample recommendation starts from your process, not from a grade list. When you contact Censil, include the film type and structure (blown, cast, mono or coextruded), the resin, the slip package, how the antiblock is added today, the target haze and COF, the opening or blocking requirement, and the defect you are trying to fix. With that, the lead grade and a comparison grade can be sent together, each with its COA, so your first trial is a real comparison. You can talk to the technical team directly or pull the document set for the track from the Download Center.
Related: Plastic Film Antiblock · Request a sample · All news