Choosing a Silica Matting Agent for Coatings by Target Gloss

In short

Choose a silica matting agent for coatings by starting from the target gloss and the resin system, not from a grade name. Particle size sets how far gloss can drop and how the film feels; surface treatment decides compatibility, transparency and settling. Confirm the choice on measured 60°/85° gloss, haze and storage behaviour in your own film.

Most matting problems that reach a technical service desk are not really about the silica. They are about a grade that was chosen for one number on a data sheet and then asked to deliver a whole film: the right gloss, a clear appearance over dark wood, a stable can after three months and a smooth spray. This article sets out a practical order of decisions for formulators and buyers, using target gloss as the anchor.

Start from the target gloss, then define how you will measure it

Write the gloss target as a number at a stated geometry and film build, not as a word. "Satin" means different things in different plants and markets. Agree three things before any screening starts:

With that fixed, matting efficiency becomes a comparable figure: the loading needed to reach the target gloss in your system. It is the first column of any screening table.

What decides how a silica matting agent for coatings performs

Silica mats a coating by creating micro-roughness at the film surface as the film shrinks during drying or cure. Four properties shape how well and how cleanly it does that:

  1. Particle size and distribution

    Larger particles mat more efficiently and are needed for deep matt in thin or high-shrinkage films, but they raise the risk of a rough, gritty surface and visible "seeds". Finer particles give a smoother touch and better clarity at the cost of efficiency. The width of the distribution matters as much as the average: a coarse tail shows up as bits, a fine tail as lost efficiency and higher viscosity.

  2. Pore volume and structure

    Porous, high-structure silica delivers more particles per gram and therefore more matting per unit loading, but it also absorbs more resin and solvent, which raises viscosity and can change flow.

  3. Surface treatment

    An untreated surface is hydrophilic and interacts with the binder; this contributes to rheology and anti-settling. Organic or special treatments reduce that interaction, improve wetting and dispersion in many resins, and help prevent hard settling — but they change rheology, so a treated and an untreated grade at the same loading will not behave alike.

  4. Compatibility with the resin and the cure

    Waterborne, UV, solventborne and powder systems shrink and cure differently. UV films shrink little and are hard to mat; waterborne clears expose any haze; powder coatings need matting that survives melt flow. The same grade can be excellent in one and mediocre in another.

Matching the Censil coating grades to the system

The coating matting and rheology track puts forward three lead grades, each with a different job. The short rule we use with customers: waterborne systems and refined surfaces try CENSIL 230W first; systems that need organic treatment and resin compatibility try CENSIL 525L; conventional industrial, coil and powder systems build the baseline on CENSIL 560N.

GradeMaterialWhere it sits in the screening
CENSIL 230WPrecipitated matting silica, specially treatedWaterborne compatibility and refined surfaces; the first grade to test when a waterborne clear has to stay transparent while going matt.
CENSIL 525LPrecipitated matting silica, organically treatedResin compatibility and easy dispersion; the general-purpose route across wood, industrial, UV, plastic and leather coatings.
CENSIL 560NPrecipitated matting silica, untreatedBalances matting, rheology, anti-settling and cost for industrial, coil, powder and conventional systems.

We do not publish typical-value tables for these grades. The controlled TDS, lot COA and SDS are sent with the sample, so the evaluation runs on the documents that will govern supply. Grade positioning across the full family is on the specifications page.

Gloss is only the first result — check the whole film

A grade that hits the gloss target can still fail in production. Run every candidate through the same validation set so the comparison is fair:

DimensionSignal to checkWhat it tells you
Gloss60° / 85° gloss and matting efficiencyThe matting result
Transparency and hazeClear-coat transparency and surface appearanceHigh-end appearance fit
Tactile feelFineness, slip and soft-touch characterProduct differentiation
Dispersion and viscosityDispersing time, system viscosity, storage stabilityProduction fit
Anti-settling and sagCan settling, sagging and film-build controlDelivery stability

Two checks are often skipped. First, look at clears over a dark substrate, where haze and a milky cast are obvious; a panel over white hides them. Second, put cans into storage and check for settling and whether it redisperses by hand stirring. Hard sediment discovered at a customer's site costs far more than an extra week of bench time.

A practical screening sequence

  1. Write the brief

    Resin system, waterborne or solventborne, cure route, target gloss at a stated geometry, film build, application method and the current matting agent with its loading. This is what the product selector and our application review start from.

  2. Screen a lead grade against contrasts

    Test the lead grade for your system alongside at least one contrast grade with a different surface treatment, each at two or three loadings bracketing the expected level. That turns a single data point into a curve of gloss against loading.

  3. Hold the dispersion process constant

    Use the dispersing equipment, speed and time you use in production. Matting efficiency and grit both depend on it, and a lab dispersion that is gentler or harsher than the plant's will mislead.

  4. Read the full validation set

    Measure gloss, then haze, feel, viscosity and settling after storage. Rank candidates on the property that most often causes your complaints, not only on loading.

  5. Confirm on a production-scale trial

    Repeat with a second lot to see lot-to-lot variation against your gloss tolerance before writing the grade into a specification.

When to change the grade rather than the loading

Raising the loading is the usual first response when gloss is too high, but it also raises viscosity and can cloud a clear. Signs that a different grade is the better fix:

What to send when you request samples

A useful sample request includes the coating type and resin, waterborne or solventborne, the cure route, target gloss and geometry, film build and substrate, current matting agent and loading, and the problem you want solved — haze, settling, sheen, feel or cost. With that, we can propose a lead grade plus contrast samples, each with a COA, so your trial is a real comparison. The TDS, COA and SDS for CENSIL 230W, CENSIL 525L and CENSIL 560N can also be pulled from the Download Center before you start.

Final performance, compliance and application fit follow the supplier's latest TDS, the lot COA and your own test results.

Screening matting silica for a new finish?Send your resin system, target gloss and current matting agent, and we will propose a lead grade plus contrast samples with COA.
Talk to an expert

Related: Coating Matting & Rheology  ·  Request a sample  ·  All news